ASO-EZ4-Plus_Product-information_0916.pdf
2 Pages
201 KB
Download
<h1>ASO-EZ4-Plus_Product-information_0916.pdf</h1> <p>Product information <br />Screed mortar</p> <p>ASO®-EZ4-Plus <br />Rapid setting, water repellent pre-blended dry mortar <br />CT-C50-F6-A9</p> <p>Technical data: <br />Basis: </p> <p>special cement, additives, aggregate</p> <p>Classification: EN 13813 CT-C50-F6-A9 <br />Application/ <br />substrate temp*: </p> <p>+5°C to + 25°C</p> <p>Working time*: </p> <p>approx. 60 minutes</p> <p>Water addition: <br /> <br /> </p> <p>1.6 –2.0 l/25 kg ASO®-EZ4-Plus <br />(6.5 – 8.0 % water) <br />semi-dry consistency - stiff-plastic</p> <p>Mixing method: </p> <p>Forced paddle mixer, free fall mixer</p> <p>Consumption: approx. 20 kg ASO®-EZ4-Plus <br />per m²/cm screed thickness <br />Foot traffic after*: </p> <p>approx. 6 hours</p> <p>Ready to install finishes*: approx. after 3 days <br />Fully cured after*: </p> <p>approx. 7 days</p> <p>Fire rating: A1 in accordance with resolution 96/603/EG <br />Packaging: </p> <p>25 kg bag</p> <p>STAIRS/CoS/TM</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafnstrasse 2–8 <br />D-32760 Detmold (Germany) <br />Tél <br />+49-5231-953-00 <br />Fax +49-5231-953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>09/16</p> <p>Area of application: <br />• ASO®-EZ4-Plus is a fibre-reinforced pre-blended factory <br />produced mortar for producing water repellent cement-based <br />screeds, which develop high early strength and can receive floor <br />finishes early. Can be used for bonded, unbonded or floating <br />quick setting screeds as well as for heated screeds as a wearing <br />surface or a substrate for tiles, slabs, textile flooring, parquet or <br />vinyl. Due to its water repellent properties, ASO®-EZ4-Plus offers <br />increased protection against frost damage and efflorescence <br />when used as a rapid hardening mortar bed for the installation of <br />natural stone, tiles and slabs in exterior and wet areas, on <br />balconies, terraces, loggia, steps, in swimming pools, wet rooms, <br />car washes and water containers.</p> <p>Subject to changes. Consult current technical data sheet for most recent information.</p> <p>*) Values relate to +23° C and 65% relative humidity.</p> <p>2 05528</p> <p>Product preparation: <br />For mixing we recommend the use of suitable mechanical equipment, batch <br />mixers, screed mixers with a 65 mm pipe diameter or other conventional <br />screed mixers e.g. PFT, Putzmeister Mixocret or similar. Pay attention to the <br />moisture content of the aggregate and avoid excess water. The working <br />time is approx. 60 minutes at +20° C. Mixing, application and finishing <br />must follow each other swiftly. Only measure out areas that can be <br />completed within this working time. For bonded screeds firstly brush <br />ASOCRET-HB-flex onto the prepared, e.g. mechanically abraded, concrete <br />substrate. Lay the screed into the wet slurry coat.</p> <p>ASO®-EZ4-Plus</p> <p>1 Placing the edge isolating strip RD-SK50</p> <p>2 Filling the clean mixing bucket with screed <br />mortar</p> <p>3 Mixing the screed mortar with suitable <br />mixing technology and prescribed water <br />quantity</p> <p>4 Spreading the screed mix</p> <p>5 Compacting the screed mortar</p> <p>6 Striking off the screed mortar with a <br />suitable straightedge</p> <p>Minimum nominal thickness to DIN 18560:</p> <p>Rapid setting, water repellent <br />pre-blended dry mortar <br />CT-C50-F6-A9</p> <p>Beneath tiles</p> <p>40 mm on insulation or separating <br />layer *2)</p> <p>Beneath parquet, carpet, <br />linoleum or PVC</p> <p>30 mm on insulation or separating <br />layer *2)</p> <p>Properties: <br />• Water repellent <br />• Protects against efflorescence <br />• Fibre-reinforced <br />• High application assurance <br />• Consistent screed quality <br />• For interior, exterior and under <br />water areas <br />• Long working time <br />• Foot traffic after 6 hours <br />• For the early installation of tiles <br />• Can be heated after 3 days <br />according to technical <br />regulations</p> <p>In general</p> <p>10 mm bonded</p> <p>*2) R eductions in thicknesses are possible as a result of structural <br />calculations and measurements by means of product characteristics. <br />Application: <br />The substrate must be dry, load-bearing, adequately flat, free from <br />penetrating cracks and free from separating substances such as e.g. oil, <br />paint, laitance layers and loose components. It must have a largely closed <br />surface texture and a surface condition and strength commensurate with its <br />type. For application and installation, the general guidelines for cementbased screeds in accordance with DIN 18560 and DIN 18353 are <br />applicable.</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold <br />04 <br />2 05528 <br />EN 13813 <br />ASO®-EZ4-Plus <br />Cement screeding mortar <br />for use in buildings <br />CT-C50-F6-A9 <br />Reaction to fire 96/603/EG: <br />Release of corrosive substances: <br />Compressive strength: <br />Flexural strength: <br />Resistance to wear: </p> <p>7 Rubbing up and finishing the screed <br />surface <br />A1fl <br />CT <br />C50 <br />F6 <br />A9</p>
