ASODUR-SG2_Product-information_1016.pdf
2 Pages
194 KB
Download
<h1>ASODUR-SG2_Product-information_1016.pdf</h1> <p>Product information <br />Primer</p> <p>ASODUR®-SG2 <br />Special epoxy resin based primer for <br />horizontal surfaces</p> <p>Technical Data: <br />Basis: </p> <p>two component epoxy resin</p> <p>Colour: </p> <p>light grey</p> <p>Foot traffic after: </p> <p>approx. 12 hours at +23 °C</p> <p>approx. 7 days at +23 °C</p> <p>Pot life: <br /> </p> <p>approx. 60 minutes at +23 °C <br />approx. 30 minutes at +30 °C</p> <p>Substrate/material/ <br />application temperature: </p> <p>+8°C to +30°C</p> <p>Consumption: </p> <p> in. 600–1000 g/m² dependent on the <br />m <br />absorption of the substrate and the area <br />of application</p> <p>Compressive strength: </p> <p>approx. 80 N/mm²</p> <p>Flexural strength: </p> <p>approx. 30 N/mm²</p> <p>WVTR in µ (DIN16 726, <br />on a free film): </p> <p>approx. 738.552</p> <p>Packaging: 2 kg, 5 kg and15 kg-containers <br />(Components A and B are delivered <br />at a predetermined mix ratio.)</p> <p>Areas of application: <br />• ASODUR®-SG2 is used as a primer on still damp concrete or <br />bonded screeds, which are to be covered with floor finishes <br />such as tiles amongst others. <br />• ASODUR®-SG2 is an effective protection against the <br />formation of osmosis bubbles where there is moisture <br />penetrating from the rear. <br />• ASODUR®-SG2 is used as a special primer on oil <br />contaminated, but previously cleaned concrete substrates. <br />• Capillary breaking epoxy grout in pool edge details.</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />Tél <br />+49-5231-953-00 <br />Fax +49-5231-953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>10/16 STAIRS/CoS/TM</p> <p>Fully cured after: </p> <p>Subject to changes. Consult current technical data sheet for most recent information.</p> <p>Overcoat after: approx. 12 - 24 hours at +23 °C</p> <p>2 05655</p> <p>ASODUR®-SG2 <br /> Special epoxy resin based <br />primer for horizontal surfaces</p> <p>Properties: <br />• low solvent, moisture tolerant <br />two component epoxy resin for <br />floors <br />• high sd value <br />• acts as a barrier against <br />capillary rising oils <br />• very good adhesion to damp <br />concrete substrates <br />• barrier against Radon</p> <p>Product preparation: <br />Component A and component B are delivered at a predetermined mixing <br />ratio. Tip component B into component A. Ensure that the hardener drains <br />completely from its container. Mix both components together with a <br />suitable mixer (e.g. drill with paddle) at 300 rpm. Ensure to also stir at the <br />sides and bottom so that the hardener is evenly dispersed. Stir for as long <br />as necessary until the mixture is homogenous (free from streaks); mixing <br />time approx. 3 minutes. During the mixing process the material <br />temperature should be approx. +15°C. Do not use the mixed material <br />directly from the supplied packaging. Decant the material into a clean <br />container and mix through thoroughly once again.</p> <p>1 Load-bearing concrete substrate</p> <p>2 Cleaning the floor substrate</p> <p>3 Priming and suitable tools</p> <p>4 Puncture the lid of the hardener <br />component</p> <p>5 Completely emptying the hardener <br />into the resin</p> <p>6 Mixing, decanting and mixing againy</p> <p>7 Application of the primer on the floor</p> <p>8 Fully broadcast the fresh primer <br />with quartz sand</p> <p>Priming <br />Apply ASODUR®-SG2 to saturation on to the cleaned floor substrate with <br />a rubber squeegee or a lamb’s wool roller, thoroughly work into the <br />surface with a priming brush and back-roll evenly with a short nap paint <br />roller. Blind the fresh primer with quartz sand. <br />Capillary grout in pool edge details <br />ASODUR®-SG2 is used as a capillary breaking grout in pool edge details <br />with a high water level. Mix the resin/hardener of ASODUR®- SG2 at the <br />pre-determined mix ratio and mix in 0.1 – 0.6 mm quartz sand at a mix <br />ratio of 1 : 1 (1 part by volume of mixed resin : 1 part by volume of quartz <br />sand) and fill out into the prepared capillary breaking joint. After approx. <br />15 minutes, fully blind the filled grouted joint with 0.1 – 0.6 mm quartz <br />sand. It is essential to prevent the sand from sinking.</p> <p>Application: <br />The surface to be treated must be dry to matt damp, sound, load-bearing <br />and have a good key. It must be free from separating or adhesion <br />inhibiting substances such as e.g. dust, laitance, grease, rubber residues, <br />paint residues and similar. Dependent on the condition of the substrate, <br />use suitable preparation measures such as e.g. shot blasting, scabbling, <br />planing, brushing, sweeping, vacuuming and grit blasting, high pressure <br />water blasting. Appropriate to each particular substrate, the following <br />criteria are also to be fulfilled: <br />Cement-based areas: <br />• Quality of the concrete: min. C 20/25 <br />• Quality of the screed: min. EN 13813 CT-C25-F4 <br />• Quality of the render: min. P IIIa/P IIIb <br />• Age: min. 28 days <br />• Tensile adhesion strength: 0.8 N/mm2</p> <p>1119</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 · D-32760 Detmold <br />06 <br />2 05655 <br />EN 1504-2</p> <p>ASODUR -SG2 <br />®</p> <p>Surface protection product - Impregnation <br />Principle 1.2 <br />Capillary water absorption <br />and water permeability </p> <p>w < 0,1 kg/m2 × h0,5</p> <p>Penetration depth </p> <p>Class I < 10 mm</p> <p>Tensile adhesion strength <br />by pull-off test </p> <p>≥ 1,5 (1,0) N/mm²</p> <p>Reaction to fire <br />Class E <br />Hazardous substances In compliance with <br />5.3 EN 1504-2</p> <p>Tensile adhesion values (EN 246324)</p> <p>Tensile adhesion values (DIN 52104, pt 1) <br />Freeze-thaw cycles <br />ASODUR®-SG2</p> <p>ASODUR®-SG2 <br />Fresh concrete (after 5 days)</p> <p>0.8 N/mm2</p> <p>Fresh concrete (after 5 days)</p> <p>0.9 N/mm2</p> <p>Concrete 28 days (saturated)</p> <p>3.8 N/mm2</p> <p>Concrete 28 days (saturated)</p> <p>3.6 N/mm2</p> <p>Concrete 28 days (dry)</p> <p>4.0 N/mm</p> <p>Concrete 28 days (dry)</p> <p>3.1 N/mm2</p> <p>Concrete 28 days (saturated)</p> <p>4.1 N/mm2</p> <p>Concrete 28 days (saturated)</p> <p>—</p> <p>Concrete 28 days (dry)</p> <p>5.3 N/mm</p> <p>Concrete 28 days (dry)</p> <p>3.5 N/mm2</p> <p>2</p> <p>2</p> <p>9 Completed floor</p>
