Reference: L15-401 / 11.11.2016
Product Declaration - LEED® v4 Building Design and Major Renovations
MANUFACTURER
SCHOMBURG GmbH & Co. KG
PRODUCT NAME
ASODUR-SG3-Superfast
PRODUCT
Rapid setting two component epoxy resin, primer, mortar, drainage resin and casting resin. For
CHARACTERISTICS
priming cement-based surfaces, which are to be coated with ASODUR-/INDUFLOOR systems. For
SCHOMBURG GmbH & Co. KG Aquafinstraße 2 32760 Detmold Deutschland
producing repair mortars, which will be trafficked again promptly. For producing levelling compounds and scratch coats as a substrate preparation measure before applying coatings. Can be used to flood repair cracks in screeds to DIN EN 13813. For producing epoxy resin screeds, repair mortars and drainage mortars. Tested to EN 1504-2. Very low emissions - GEV EMICODE EC1-R PLUS.
Product Rating LEED Category
LEED Credit
max. influenced score
Degree of fulfillment %
For the product exists an EPD which can be used for the calculation of the Life-Cycle Assessment of the building under MR Credit 1 Building Life-Cycle Impact Reductions / Option 4. The product contributes toward satisfying MR Credit 2 "BPDO - Environmental Product Declarations" under LEED. The product contributes toward satisfying EQ Credit 2 "Low Emitting Materials" under LEED. Materials & Ressources
Credit 1: Building Life-Cycle Impact Reductions (Option 4: LCA)
1-3 Points
Credit 2: BPDO - Environmental Product Declarations
1-2 Points
100%
Option 1: Environmental Product Declaration
1 Point
50%
Option 2: Multi-Attribute Optimization
0%
Credit 3: BPDO - Sourcing of Raw Materials
Option 1: Raw Material Source and Extraction Reporting
Option 2: Leadership Extraction Practices
Credit 4: BPDO - Material Ingredients
Indoor Environmental Quality
Option 1: Material Ingredient Reporting
Option 2: Material Ingredient Optimization
Option 3: Product Manufacturer Supply Chain Optimization
Credit 2: Low Emitting Materials
About LEED & Products - www.usgbc.org This declaration helps to assess products easily according to the certification system LEED® v4 Building Design and Major Renovations (excluded HEALTHCARE and SCHOOLS). Products are not reviewed or certified by LEED. LEED credit requirements cover the performance of materials in aggregate, not the performance of individual products or brands. For more information about LEED visit www.usgbc.org/leed. The project team or the manufacturer is responsible to declare the compliance with the project requirements to achieve LEED points. Below you find an explanation of the symbols. Detailed information are on the next pages.
ü
Product helps to achieve the LEED point in the Credit
22%
X% of the product contributes toward satisfying the credit
¡
Credit is not applicable to this product
—
Required data not specified - for required data contact manufacturer
X
Credit requirements are not fulfilled
Page: 1
MR Credit 1: Building Life-Cycle Impact Reductions (Option 4: LCA) Intent To encourage adaptive reuse and optimize the environmental performance of products and materials. Requirement Environmental Product Declaration (EPD) can be used in Credit "MR 1: Building Life-Cycle Impact Reductions" in Option 4 "Whole-Building Life-Cycle Assessment" for the calculation of the Life-Cycle Assessment of the building. If no EPD exitst, generic datasets will be used. Detailed Rating
Whole-Building Life-Cycle Assessment
Compliance
For the product exists an EPD.
General Information No. Product name
A1
Manufacturer
ASODUR-SG3-
SCHOMBURG
Superfast
GmbH & Co. KG
Option 4: Mass [%]
Page: 2
MR Credit 2: BPDO - Environmental Product Declarations Intent To encourage the use of products and materials for which life-cycle information is available and that have environmentally, economically, and socially preferable life-cycle impacts. To reward project teams for selecting products from manufacturers who have verified improved environmental life-cycle impacts. Requirement Achieve one or more of the options below, for a maximum of 2 points. Option 1: Environmental Product Declaration (1 Point) Use at least 20 different permanently installed products sourced from at least five different manufacturers, for which an Environmental Product Declaration exist. Proof - weighted value [%]: ▪ Product-specific declaration - 25 % ▪ Industry-wide (generic) EPD - 50 % ▪ Product-specific Type III EPD - 100 % Option 2: Multi-Attribute Optimization (1 Point) 50 % of all materials (based on the material costs of the project) must be less than the industry average in terms of environmental emissions. Third party certified products that demonstrate impact reduction below industry average in at least three of the following categories are valued at 100 % of their cost for credit achievement calculations. ▪ global warming potential (greenhouse gases), in CO2e; ▪ depletion of the stratospheric ozone layer, in kg CFC-11; ▪ acidification of land and water sources, in moles H+ or kg SO2; ▪ eutrophication, in kg nitrogen or kg phosphate; ▪ formation of tropospheric ozone, in kg NOx or kg ethene; ▪ and depletion of nonrenewable energy resources, in MJ. Regional products (within 160 km = 100 Milen) are double-weighted. Detailed Rating General Information No. Product name
Option 1: Environmental Product Declaration Mass [%] 100% 100%
EPD Program Operator
EPD Type - Weighted Value [%]
Third Party Certification Program**
Institut Bauen und Umwelt
Industry-wide (generic) EPD -
e.V. (IBU)
not specified ***
Institut Bauen und Umwelt e.V.
(IBU)
Location* see location see location
* see explanation "Location Valuation Factor" on page 10 ** Demonstrate impact reduction below industry average *** Evidence is verified by: not specified
Page: 3
MR Credit 3: BPDO - Sourcing of Raw Materials 1/2 Intent To encourage the use of products and materials for which life cycle information is available and that have environmentally, economically, and socially preferable life cycle impacts. To reward project teams for selecting products verified to have been extracted or sourced in a responsible manner. Requirement Achieve one or more of the options below, for a maximum of 2 points. Option 1: Raw Material Source and Extraction Reporting (1 Point) Use at least 20 different permanently installed products sourced from at least five different manufacturers, who published a sustainability report of their suppliers. ▪ Manufacturer declared corporate sustainability report - 50 % ▪ Third-party verified corporate sustainability report (CSR) according to Global Reporting Initiative (GRI) Sustainability Report, Organisation for Economic Cooperation and Develoment (OECD) Guidelines for Multinational Enterprises, U.N. Global Compact: Communication of Progress or ISO 26000: 2010 Guidance on Social Responsibility - 100 % Option 2: Leadership Extraction Practices (1 Point) 25 % of all materials (based on the material costs of the project) must have at least an extended producer responsibility (closed loop or tage back programm) or are made from SAN certified bio-based materials, FSC certified wood, recycling materials (post-consumer recycled content plus one-half of the pre-consumer content), salvaged or reused materials. Detailed Rating General Information No. Product name
Option 1: Raw Material Source and Extraction Reporting Mass [%] 100%
percentage influential degree (weighted ASODUR-SG3-
not specified 0%
contribution) A1
Corporate Sustainability Report Type - Weighted Value [%]
not specified
Page: 4
MR Credit 3: BPDO - Sourcing of Raw Materials 2/2 Detailed Rating General Information
Option 2: Leadership Extraction Practices Extended
No. Product name
Mass
Producer
[%]
Responsibility -
Salvaged SAN [%]**
FSC [%]***
material [%] ****
Post-
Pre-
Consumer [%]
Content [%] ASODUR-SG3-
see location
Location*
* see explanation "Location Valuation Factor" on page 10 ** SAN certified Content [%] *** FSC certified Content [%] **** Content of reused and salvaged materials [%]
Page: 5
MR Credit 4: BPDO - Material Ingredients Intent To encourage the use of products and materials for which life-cycle information is available and that have environmentally, economically, and socially preferable life-cycle impacts. To reward project teams for selecting products for which the chemical ingredients in the product are inventoried using an accepted methodology and for selecting products verified to minimize the use and generation of harmful substances. To reward raw material manufacturers who produce products verified to have improved life-cycle impacts. Requirement Achieve one or more of the options below, for a maximum of 2 points. Option 1: Material Ingredient Reporting (1 Point) Use at least 20 different permanently installed products sourced from at least five different manufacturers, which published reports or data sheets with all ingredients. Proofs (Weighted Value 100 %): ▪ Manufacturer Inventory ▪ Health Product Declaration (HPD) ▪ Cradle to Cradle (Cradle to Cradle v2 Basic or Cradle to Cradle v3 Bronze) Option 2: Material Ingredient Optimization (1 Point) 25 % of all materials (based on the material costs of the project) must be certified by Green Screen, Cradle to Cradle or REACH. ▪ GreenScreen v1.2 List Translator - 100 % ▪ GreenScreen v1.2 Assessment - 150 % ▪ Cradle to Cradle v2 Gold - 100 % ▪ Cradle to Cradle v2 Platinum - 150 % ▪ Cradle to Cradle v3 Silver - 100 % ▪ Cradle to Cradle v3 Gold or Platinum - 150 % ▪ REACH - 100 % Option 3: Product Manufacturer Supply Chain Optimization (1 Point) 25 % of all materials (based on the material costs of the project) are sourced from product manufacturers who engage in validated and robust safety, health, hazard, and risk programs and are sourced from product manufacturers with independent third party verification of their supply chain (e.g. ISO 14001 & OHSAS 18000). Detailed Rating
General Information
Option 1:
Option 2:
Material
Ingredient Ingredient Reporting Optimization
No.
Certification Product name
Type of
Program
Reporting
Weighted
Value [%]
100% 100%
not
specified
not specified not specified
see location see location
* see explanation "Location Valuation Factor" on page 10
Page: 6
EQ Credit 2: Low Emitting Materials 1/4 Intent To reduce concentrations of chemical contaminants that can damage air quality, human health, productivity, and the environment. Requirement This credit includes requirements for product manufacturing as well as project teams. It covers volatile organic compound (VOC) emissions into indoor air and the VOC content of materials, as well as the testing methods by which indoor VOC emissions are determined. Different materials must meet different requirements to be considered compliant for this credit. Category
Requirement • General Emissions Evaluation for paints and coatings applied to walls, floors, and ceilings
Interior paints and coatings applied on site
• VOC content requirements for wet applied products
Interior adhesives and sealants applied on site including flooring
• General Emissions Evaluation
adhesive
Flooring
• General Emissions Evaluation • Composite Wood Evaluation
Composite wood
Proof: ultra-low-emitting formaldehyde (ULEF), no added formaldehyde resins (NAUF) or salvaged and reused wood
Ceilings, walls, thermal, and acoustic insulation
• General Emissions Evaluation • Furniture Evaluation
Furniture (include in calculations if
Proof: ANSI/BIFMA e3-2011 §7.6.1, ANSI/BIFMA e3-2011 §7.6.2, CDPH Standard Method v1.1-2010 or
part of scope of work)
salvaged or reused furniture
Detailed Rating General Information No. Product name
Mass [%]
Product Category Calculations
Budget Calculation Method
Category
Assembly Type
Emissions Criteria
Inherently Nonemitting
see below Interior adhesives and sealants
General Emissions Evaluation and VOC Content
No
Page: 7
EQ Credit 2: Low Emitting Materials 2/4 Detailed Rating
Criteria Met
TVOC Range after 14 days
Product Type
see below AgBB Testing and
Regulation
Actual
VOC [g/l]
Product name
VOC Content Allowable
General Emissions Evaluation
Evaluation Scheme (2010) *
5,0 mg/m3 oder
SCAQMD Rule
Ceramic tile
mehr
1168
adhesives
65 g/l
0 g/l
Other remarks on classification *The product is certified by the EMICODE. The content of formaldehyde is < 10 µg/m³ at 28 days. The content of solvent is 0% (0g/l).
EQ Credit 2: Low Emitting Materials 3/4 Detailed Rating
see below
N/A
Composite Wood Mass [%]
Page: 8
EQ Credit 2: Low Emitting Materials 4/4 Detailed Rating
Furniture Mass [%]
Page: 9
Location Valuation Factor Information Several credits in the MR section include a location valuation factor, which adds value to locally produced products and materials. The intent is to incentivize the purchase of products that support the local economy. Products and materials that are extracted, manufactured, and purchased within 100 miles (160 kilometers) of the project are valued at 200 % of their cost. For a product to qualify for the location valuation factor, it must meet two conditions: all extraction, manufacture, and purchase (including distribution) of the product and its materials must occur within that radius, and the product (or portion of an assembled product) must meet at least one of the sustainable criteria (e.g. FSC certification, recycled content) specified in the credit. Products and materials that do not meet the location criteria but do meet at least one of the sustainability criteria are valued 100 % of their cost (i.e. the valuation factor is 1). The distance must be measured as the crow flies, not by actual travel distance. The point of purchase is considered the location of the purchase transaction. For online or other transactions that do not occur in person, the point of purchase is considered the location of product distribution. Detailed Rating General Information No. Product name
Location Mass [%]
Extraction
Manufacture
Purchase (including distribution)
Double weighting depends on building site not specified
D-32760 Detmold
Page: 10
Notice: This declaration is a product of HOINKA GmbH. This data sheet is published in the online database greenbuildingproducts.eu. The data sheet is only valid as LEED evidence in conjunction with the manufacturer's declarations and product certificates that prove the information given in this declaration. This declaration is no official certificate in terms of LEED. The contents are based on manufacturer specifications. In spite of a diligent treatment of all information HOINKA GmbH cannot guarantee the actuality or correctness of the published data. The interpretation of the LEED criteria requirements can differ and depend on the project and the scope of application. In spite of a diligent treatment of all information HOINKA GmbH cannot guarantee the correctness of evaluation in terms of the LEED requirements. The user of this declaration, the consumer of the product and the consultant/planner, who is advising this product in any construction projects, is responsible by himself to proof all data published in this document and to verify the permissibility for the designated application. The content of this data sheet does not manifest any legal relationship. With the publication of a new edition, this declaration can no longer be considered to be valid. The latest version is available in the internet.
Contact: HOINKA GmbH - greenbuildingprodcuts.eu Nobelstraße 15 D-70569 Stuttgart Tel. +49 711 62049-340 Fax +49 711 62049-349 www.greenbuildingproducts.eu contact@greenbuildingproducts.eu Imprint: HOINKA GmbH - greenbuildingprodcuts.eu Lembergweg 7/1 D-71067 Sindelfingen CEO: Dipl.-Ing. Thomas Hoinka Page: 11