CRISTALLFUGE_Produktinformation_0122.pdf
2 Pages
435 KB
Download
<h1>CRISTALLFUGE_Produktinformation_0122.pdf</h1> <p>joint mortar</p> <p>Application <br />1. Mix CRISTALLFUGE with clean water in a clean mixing bucket. Add <br />1.25-1.5 l water depending on the desired consistency and the type of <br />ceramic to be joined, add 5 kg CRISTALLFUGE (5.0–6.0 l water for <br />20 kg CRISTALLFUGE), and then stir into a homogeneous, smooth <br />compound. We recommend mixing with a suitable stirrer. After an <br />activation time of 4 min., the joint mortar is stirred again. In order to <br />avoid colour differences, the mix ratio must always be kept the same. <br />2. CRISTALLFUGE is added to the wall or floor areas with a suitable <br />jointing board and pulled diagonally to the joint cleanly, so that the joint <br />cross-section is filled completely. Do not scatter dry joint mortar powder. <br />3. After applying the joint mortar (control via finger test), wash the surface <br />first with a moist sponge board. After approx. 5–15 minutes, depending <br />on the absorbency of the covering, wash after cleanly with the sponge <br />board.</p> <p>joint mortar <br />CRISTALLFUGE</p> <p>Please refer to the currently valid technical data sheet for <br />additional instructions.</p> <p>Properties <br />• For interior <br />• 1 to 6 mm joint width <br />• Quickly washable <br />• Smooth consistency <br />• Vapour permeable <br />• Cures without cracks <br />• Good binding and wash-off properties <br />• For porcelain stoneware and many other coverings <br />• Colours matched to the ESCOSIL-2000 and <br />ESCOSIL-2000-ST silicone system <br />Areas of use <br />• CRISTALLFUGE is suited especially well to <br />grouting absorbent ceramics consisting of <br />earthenware and vitrified tiles, and it may be <br />used for joint widths up to 6 mm in interior areas, <br />mainly on walls, in dry, damp, and wet areas.</p> <p>2 CRISTALLFUGE, suitable tools</p> <p>3 Fill the joint mortar into a clean mixing <br />bucket</p> <p>4 Mix the joint mortar</p> <p>5 Apply the joint mortar</p> <p>6 Sliding diagonally across excess joint mortar</p> <p>7 Moisten and press out the clean sponge <br />board</p> <p>8 Emulsify the joint mortar after setting</p> <p>9 Rinsing off surfaces diagonally to the joint <br />direction</p> <p>10 Finished and jointed wall surface</p> <p>Consumption table <br />Joint width <br />(in mm)</p> <p>Joint depth <br />(in mm)</p> <p>Approx. <br />consumption in m2 <br />(in kg)</p> <p>2.0</p> <p>1.5</p> <p>2.0</p> <p>0.58</p> <p>10.0 × 10.0</p> <p>3.0</p> <p>6.0</p> <p>0.70</p> <p>15.0 × 15.0</p> <p>3.0</p> <p>6.0</p> <p>0.49</p> <p>20.0 × 20.0</p> <p>3.0</p> <p>8.0</p> <p>0.49</p> <p>20.0 × 25.0</p> <p>3.0</p> <p>8.0</p> <p>0.45</p> <p>30.0 × 30.0</p> <p>5.0</p> <p>8.0</p> <p>0.55</p> <p>30.0 × 40.0</p> <p>4.0</p> <p>10.0</p> <p>0.48</p> <p>30.0 × 60.0</p> <p>4.0</p> <p>10.0</p> <p>0.41</p> <p>Tiles/boards <br />format (in cm) <br />2.0 ×</p> <p>DIN EN <br />äß</p> <p>888 <br />13</p> <p>gem</p> <p>Flexible fine joint mortar, <br />1–6 mm</p> <p>Application <br />• After the bedding mortar sets, scratch out the joints sufficiently deep. <br />• Next, clean the tiled finish sufficiently damp. <br />• The bedding mortar must be fully set, since otherwise discolourations in <br />the grout finish could result. <br />• Pre-moisten strongly absorbing coverings with water equally. <br />• Joint edges must be clean and free of separating substances. <br />• The time of grouting of the tiles set in the thin-bed depends on the thinbed mortar and amounts to approx. 3 to 72 hours. In case of thick-bed <br />laying, the mortar bed must be sufficiently firm and equally dry. <br />• Do not grout on surfaces with different surfaces temperatures <br />(e.g. due to sun exposure). <br />• The consistency of joint mortar must be specified depending on <br />the absorbency of the covering and substrate to be grouted.</p> <p>1 Available floor surface, bonding bed is set</p> <p>CG2</p> <p>* Informationen über das Emissionsniveau von flüchtigen Stoffen in <br />der Raumluft, die bei Inhalation Gesundheitsrisiken, auf einer Skala <br />von Klasse A + (sehr emissionsarm) bis C (hohe Emissionen), darstellen.</p> <p>joint mortar <br />CRISTALLFUGE <br />Flexible fine joint mortar, 1–6 mm</p> <p>Cement, high-quality additives, <br />Cementitious aggregate</p> <p>Colours</p> <p>white, silver grey, Manhattan, titanium grey, Jura <br />beige</p> <p>Classification</p> <p>EN 13888 CG 1</p> <p>Application temperature</p> <p>+5 °C to +25 °C</p> <p>Pot life*</p> <p>approx. 60 minutes</p> <p>Water addition</p> <p>5.0–6.0 l water: 20 kg CRISTALLFUGE <br />1.2–1.5 l water: 5 kg CRISTALLFUGE</p> <p>Consumption</p> <p>see consumption table</p> <p>Foot traffic* <br />Withstands loads*</p> <p> fter approx. 12 hours <br />a <br />earliest after approx. 2 days</p> <p>Packaging</p> <p>5 kg foil bag, <br />10 kg foil bag</p> <p>*at +23 °C, 50 % rel. humidity</p> <p>Colours*</p> <p>silver grey</p> <p>white</p> <p>jasmine</p> <p>pergamon</p> <p>beige</p> <p>caramel</p> <p>Jura beige</p> <p>brown</p> <p>nut brown</p> <p>grey</p> <p>medium grey</p> <p>Titanium grey</p> <p>graphite</p> <p>Bahama beige</p> <p>sand grey</p> <p>* Colour deviations are due to printing technology.</p> <p>SCHOMBURG GmbH <br />Aquafinstraße 2–8 <br />D-32760 Detmold (Germany) <br />Telephone +49-5231-953-00 <br />Fax <br />+49-5231-953-333 <br />www.schomburg.com</p> <p>01/22 TS/Tet/LiW</p> <p>Basis</p> <p>Subject to change without prior notification. The valid issue of the corresponding technical bulletin legally applies.</p> <p>Technical data</p>
